JL/JT Gauge Package (triple pod 2018+)
JL/JT Gauge Package (triple pod 2018+)
AEM BOOST/VACUUM DIGITAL GAUGE
AEM’s 30-0306 X-Series -30in/Hg~35PSI / -1~2.5BAR Digital Boost Display gauge combines incredible looks, increased readability and a multitude of new, easy-to-use features! It is a must for users who want highly accurate boost pressure readouts up to 35 PSI or 2.5 BAR in their high performance vehicle. Visual improvements include a bright center LED display that is 87% larger than our original digital gauges and provides better readability. A sweeping green LED “needle” lines the edge of the gauge face for quick reference. A 33% overall increase in the gauge face display makes it easier to see at a glance. X-Series Digital Gauges include new technological features that make them easier to use. Two buttons on the faceplate deliver programmability for peak/recall, standard or metric center LED readout and sweeping LED needle, and user-selectable threshold warnings. The gauges are AEMnet CAN-bus enabled, so they can be daisy chained together for use with the Infinity ECU, Series 2 EMS, AQ-1 Data Logger, or 3rd party EMS or logger that accepts AEMnet. 0-5V analog outputs are also included for inputting into data loggers and engine management systems.
AEM WIDEBAND AIR/FUEL DIGITAL GAUGE
AEM’s X-Series OBDII Wideband UEGO AFR Sensor Controller Gauge (PN 30-0334) provides tuners who are using piggyback tuning modules or open source software with the ability to view AFR through the factory CAN-bus stream that is output by the factory ECU, and deliver the most accurate, safe and powerful tune. The 30-0334 X-Series OBDII Wideband Gauge is validated to work with HPTuners VCM Suite software! The X-Series Wideband AFR OBDII Gauge includes an OBDII pass-through connector and Bosch 4.9LSU sensor that can be free-air calibrated or used with the factory resistor calibration. Additional wiring for a 0-5v or RS232 Serial output can be added by the user for outputting to a data logger. This OBDII pass-through capability replaces the traditional AEMnet stream available in the 30-0300 X-Series Wideband AFR Gauge Controller.
Accurate AFR data is critical when tuning an engine. Running rich (very low air/fuel ratio, excessive fuel) can cause a loss in power, while running too lean (very high air/fuel ratio, not enough fuel) may result in serious engine damage. Using a wideband air/fuel controller during the tuning process allows you to monitor AFR and adjust tuning parameters to optimize them for maximum power and efficiency. AEM has a comprehensive line of highly accurate, reliable wideband air/fuel controllers that can help ensure your vehicle is optimally tuned.
DASH MOUNT | TRIPLE GAUGE POD
Transform your JL/JT’s dash into a high-performance cockpit with this mounted triple gauge pod. Custom designed for your specific vehicle, this pod mounts your gauges right on your vehicle’s dash board at near eye level where you need ‘em. With your gauges strategically stationed, you can gather engine vitals without losing sight of the task at hand. Plus, a custom gauge cluster mounted to your dash gives your ride a racecar style that’s anything but factory! Custom built to fit your vehicle’s top dash storage pocket, this triple gauge pod makes good use of a not so usable area. And, the molded design takes only a few tools and minimal effort to mount right into your factory pockets mounting points. Included is a gauge-size mounting hole cover for a clean look, but can be removed to add an additional gauge.
Prodigy Performance’s Jeep Wrangler AEM Triple Wideband/Boost gauge package, includes everything you need for your turbocharged JL/JT. The following is included in this package. 1- Boost/Vacuum Digital Gauge 2- Triple Gauge Pod 3- Digital Wideband Air/Fuel Ratio Gauge 4- Gauge-size mounting hole cover